Charts and Diagrams

How to Draw Circuit Diagrams in LaTeX with circuitikz

Draw circuit diagrams in LaTeX with circuitikz. Covers loading the package, component names, labels, voltages, currents, and branching wires, with examples.

On this page
  1. What circuitikz does
  2. Load circuitikz
  3. Draw your first circuit
  4. Component names you will use most
  5. Add labels, voltages, and currents
  6. Connect branches with coordinates
  7. Common problems
  8. Frequently asked questions

What circuitikz does

circuitikz is a package that builds on TikZ to draw electrical and electronic circuits. You draw wires with coordinates and place components with a to[...] path, which takes a component name and optional labels. The code stays short, and you control the layout.

Load circuitikz

\usepackage{circuitikz}

Pass american or european as an option to choose the symbol style, for example \usepackage[american]{circuitikz}. Use the style your course, lab, or journal expects.

Draw your first circuit

This series loop has a battery, a resistor, and a capacitor:

\documentclass{article}
\usepackage{circuitikz}

\begin{document}

\begin{circuitikz}
  \draw (0,0) to[battery1, l=$V_s$] (0,3)
    -- (2,3) to[R, l=$R$] (4,3)
    -- (4,0) to[C, l=$C$] (2,0)
    -- (0,0);
\end{circuitikz}

\end{document}

Read the path from left to right. It starts at (0,0), goes up through the battery to (0,3), runs right to (2,3), passes through the resistor to (4,3), then goes down to (4,0). From there it passes through the capacitor back to (2,0) and returns to the start. l= puts a label beside the component.

Component names you will use most

Component Name Example
Resistor R to[R, l=$R$]
Capacitor C to[C, l=$C$]
Inductor L to[L, l=$L$]
Battery battery1 to[battery1, l=$V_s$]
Voltage source V to[V, l=$V$]
Current source I to[I, l=$I$]
Plain wire short to[short]
Ground ground (a node, not a to component) \draw (0,0) node[ground] {};

Most components go inside to[...]. Ground is a node, so you place it with node[ground] at a point.

Add labels, voltages, and currents

Three keys annotate a component:

  • l= puts a label beside the component. Use l_= to place it on the other side.
  • v= draws a voltage arrow across the component.
  • i= draws a current arrow along the component.
\draw (0,0) to[R, l=$R$, v=$V_R$, i=$I_R$] (3,0);

Connect branches with coordinates

Parallel branches come from drawing a path between two wires. This example places two resistors between a top wire and a bottom wire:

\begin{circuitikz}
  \draw (0,0) to[battery1, l=$V_s$] (0,3) -- (4,3);
  \draw (0,0) -- (4,0);
  \draw (2,3) to[R, l=$R_1$] (2,0);
  \draw (4,3) to[R, l=$R_2$] (4,0);
\end{circuitikz}

If your circuit needs a junction dot where a branch meets a wire, add one with \node[circ] at (x,y) {};.

Common problems

  • The to[...] path gives an error. Path commands like to[...] only work inside circuitikz or tikzpicture. Wrap the code in \begin{circuitikz} and \end{circuitikz}.
  • A label overlaps a wire or another label. Move it to the other side with l_=, or shorten it.
  • A component is missing. Check its name against the table above. An unknown name produces an error in the log.

Frequently asked questions

Is circuitikz part of TikZ?

No. circuitikz is a separate package that uses TikZ to draw. Loading circuitikz also loads TikZ, so you do not need to load it yourself.

Which package should I use for block diagrams?

Use TikZ for block diagrams and flowcharts, and circuitikz for electrical schematics. The block diagrams and flowcharts guide covers TikZ basics.

The complete guide to charts and diagrams

Drawing Block Diagrams and Flowcharts in LaTeX
Read the guide

Keep exploring

Guides from other topics

All topics →